Coordinate Measuring Machine System
Solicitation number W7702-135575/A
Publication date
Closing date and time 2012/12/31 15:00 EST
Description
Trade Agreement: WTO-AGP/NAFTA/Canada-Peru FTA/Canada-Colombia FTA Tendering Procedures: All interested suppliers may submit a bid Attachment: None Competitive Procurement Strategy: Lowest/Lower Bid Comprehensive Land Claim Agreement: No Nature of Requirements: W7702-135575/A Kozak, Tammy Telephone No. - (204) 984-8825 Fax No. - (204) 983-7796 Defence R & D Canada Suffield has a requirement for a complete Coordinate Measuring Machine (CMM) system to verify prototype patterns prior to active testing. Many of these pieces involve complex curves obtained via equations of several exponential degrees and cannot be checked with simple radii. Parts are typically dish shaped or conical in a variety of sizes. Occasionally, parts tested through failure are reverse engineered using the CMM to provide pattern details used in modelling programs. MINIMUM MANDATORY SPECIFICATIONS: 1 Minimum range must equal or exceed 600mm x 500mm x 300mm (xyz), especially in the Z direction to accommodate deeper profiles - x and y values may be interchanged. 2 Minimum resolution must be better than 0.001 mm (0.000 04"), with high repeatability and protected, non-contact scales. 3 Movement must have ability to lock each axis individually, and fine adjustment capability is required on the two major axes as a minimum. 4 CMM must be mounted on its own granite working base, with built in method to secure the test piece (tool slots or threaded holes), including a dedicated support stand. 5 Must include manual indexing head and touch trigger probe or combination, and include both spherical-end and point-end styli of minimum 25mm working length 6 Unit must include dedicated computer system with all associated components and cables (monitor(s), keyboard, mouse etc.) with software pre-installed and tested 7 Monitor must be a minimum 19" diagonal 8 PC unit must have current components (power supply, processor, memory, hard drive, USB port) with capability exceeding the minimum requirement of the software 9 Software must be of geometric measurement specialty, capable of creating a part-based coordinate system, memorizing measuring patterns/procedures for multiple part comparison or checking. 10 Software must include option package capable of using curve equations and/or CAD drawings for part measurements and comparisons. 11 Contractor must provide on-site assembly, perform testing and system certification prior to acceptance of the unit. 12 On-site training required for 1-3 personnel for both CMM and software 13 If movement is motor driven, unit MUST have collision avoidance in software AND auto stop upon touch probe contact in any direction. 14 If movement is mechanical (ground ways and bearings), these must be covered and/or protected from dust and debris. If movement is via air bearings, unit must include either its own clean air supply OR conditioning system to meet bearing requirements. Delivery Date: Above-mentioned The Crown retains the right to negotiate with suppliers on any procurement. Documents may be submitted in either official language of Canada.
Contract duration
Refer to the description above for full details.
Trade agreements
-
World Trade Organization Agreement on Government Procurement (WTO GPA)
-
Canada-Colombia Free Trade Agreement
-
Canada-Peru Free Trade Agreement (CPFTA)
-
North American Free Trade Agreement (NAFTA)
Contact information
Contracting organization
- Organization
-
Public Works and Government Services Canada
- Address
-
11 Laurier St, Phase III, Place du PortageGatineau, Quebec, K1A 0S5Canada
- Contracting authority
- Kozak, Tammy
- Phone
- (204) 984-8825 ( )
- Fax
- (204) 983-7796
- Address
-
PO Box 1408, Room 100
167 Lombard Ave.Winnipeg, Manitoba, R3C 2Z1
Buying organization(s)
- Organization
-
Department of National Defence
- Address
-
101 Colonel By DrOttawa, Ontario, K1A0K2Canada
Bidding details
Full details regarding this tender opportunity are available in the documents below. Click on the document name to download the file. Contact the contracting officer if you have any questions regarding these documents.
Document title | Amendment no. | Language | Unique downloads | Date added |
---|---|---|---|---|
ABES.PROD.BK_WPG.B202.F8285.EBSU000.PDF | 000 |
French
|
0 | |
ABES.PROD.BK_WPG.B202.E8285.EBSU000.PDF | 000 |
English
|
2 |
Access the Getting started page for details on how to bid, and more.